Wiring Cloud — Library of Wiring Diagrams & Standard Electrical Schematics

Wiring a ceiling-mounted occupancy sensor

A ceiling-mounted occupancy sensor switches a light when it detects presence, improving convenience in hallways, laundries, garages, and driveways. In Australia, most of these fittings are connected to a 230 V AC, 50 Hz supply, so safe isolation and correct conductor identification matter more than the sensor settings.

The available models are not interchangeable. PIR units respond to changes in infrared heat, microwave units detect movement through air, and ultrasonic sensors sense movement by reflected sound. Some need a neutral wire, while others are designed for a switched-light loop; buying first and reading later often leads to incompatible parts.

Australian houses add practical constraints. Ceiling cavities in a Melbourne terrace or Brisbane Queenslander may contain old rubber cable, insulation, cobwebs, or telephone wiring, while metal-roofed and coastal homes demand suitable environmental ratings. The fitting must suit the ceiling construction, heat, moisture, and load.

Use the exact model diagram, not a generic drawing, and test the circuit before touching terminals. Electrical references can explain conventions, but they cannot establish what is hidden in your ceiling. Where mains work falls outside your experience, a licensed electrician—or an experienced “sparky”, as Aussies often say—is the sensible call.

Choose the right detector

Start with how the room is used. A PIR sensor suits a hallway with clear sightlines but may miss someone approaching along a corridor. A microwave detector can cover an open living area, although it may also sense movement beyond the room. Ultrasonic models can respond to nearby movement without maintaining a constant warm target.

Check the label for supply voltage, frequency, minimum and maximum lamp load, neutral requirement, and compatibility with LED drivers. Record the model number and read its legend. Technical labels are useful only when defined, just as the stated conditions matter in material such as Australian keno strategies; generic instructions cannot safely fill missing details.

Choose controls that match the result. Adjustable sensitivity, hold time, and daylight override help prevent short cycles and unwanted daytime operation. For enclosed or outdoor-adjacent locations, check the ingress rating and the manufacturer's specified mounting clearance; a neat location is not always a suitable one.

Match the Australian circuit

Most Australian ceiling-light circuits use active, neutral, and earth conductors, with brown or red commonly identifying active, blue or black neutral, and green/yellow earth. Older installations may predate those colours. Never assume a function from insulation alone, especially in renovated homes or cable recovered from a previous tenant.

Under AS/NZS 3000, exposed conductive parts of a fixed luminaire require protective earth continuity; an earth conductor should not be left floating. Many Australian switchboards also use RCDs or RCBOs, commonly feeding bathroom, kitchen, garage, and outdoor circuits. Protection devices supplement sound workmanship; they do not make incorrect connections safe.

A three-wire detector usually receives supply and neutral at the ceiling rose and switches the lamp through its load terminal. Follow the manual's terminal order and use secondary wiring references to cross-check the symbols. If the unit has only line and load terminals, it may be a no-neutral model with different load requirements.

Prepare the ceiling safely

Switch off the circuit breaker, isolate the lighting circuit at the switchboard, and prove the conductors are dead with an appropriate tester. Wall switches can remain energised at the ceiling rose, so their position is not evidence of isolation. Lock out the breaker where possible and keep the circuit clearly marked.

Remove the existing light fitting while supporting its weight, then inspect the rose, terminals, cable sheath, and support. Replace brittle or heat-damaged components and confirm that the ceiling cavity can carry the detector's weight. Avoid packing loose insulation around a warm driver or a terminal block.

Legacy routes are common in older Australian properties. Some renovations can be decoded with old house phone wiring, but low-voltage telephone conductors must never be repurposed as mains wiring or treated as an earth. New supply conductors should be installed and terminated to current requirements.

Terminate and secure the wiring

For a typical neutral-required unit, connect supply active to the line terminal, supply neutral to neutral, the switched output to the lamp's active conductor, and lamp neutral to supply neutral. Connect the earth to the designated earth terminal, tightening each screw evenly and leaving no loose strands under the clamp.

Do not transfer a no-neutral diagram to a model with a neutral terminal, or the reverse. Two-wire detectors may require a minimum incandescent load and can behave poorly with some LED fittings. Check the manufacturer's compatibility list, especially where dimmers, electronic drivers, or a changed lamp type are involved.

Use terminal blocks or connectors suitable for mains voltage, maintain the required conductor gauge, and place any joint in an accessible enclosure. Keep active and neutral conductors separated where required and avoid nicking insulation. A licensed electrician should resolve doubtful cable identification, missing earths, or crowded terminal blocks.

Commission and adjust the sensor

Restore power only after every conductor is enclosed and checked. Use the sensor's test mode, if provided, then walk across the detection area and confirm that the lamp starts and clears after the chosen delay. Repeated switching can reveal a loose connection, unsuitable load, or an incorrectly wired output.

Fine-tune sensitivity and hold time after the room is in normal use. Reduce microwave detection where an adjoining room or hallway triggers the lamp, and use the daylight override if lights should remain off in bright conditions. Pets, open doors, and moving hot air can also affect the pattern.

Test the RCD or RCBO using its test button at the interval stated by the manufacturer, commonly monthly in Australian households. Then check for flicker, hum, heat, or lamps that fail to extinguish. If the fitting behaves inconsistently, disconnect it before investigating rather than repeatedly cycling the breaker.

Document and maintain the installation

Label the switchboard with the room and device, and keep the model number, terminal diagram, settings, and installation date together. A clear circuit record helps the next electrician distinguish the occupancy detector from other switches, especially in crowded consumer-unit directories.

Add the sensor to routine cleaning. Dust, cobwebs, insects, and compressed insulation can distort the detection field or cause nuisance switching, while dirt on an outdoor-rated lens reduces performance. Check LED-driver compatibility again after lamp changes and arrange inspection if the unit becomes warm or operates erratically.

Now download the diagram for your exact model, record the existing conductor arrangement, and complete the safe tests before energising the circuit. If any terminal remains uncertain, leave the breaker off and have a licensed electrician check and sign off the work.